Opens in a new window
Golden Age Project GA-251 MKII Large Diaphragm Tube Condenser Microphone
Your Price: $2,799.00 CDN
or from $164 CDN/mo
The Telefunken ELA M 250/251 was made for Telefunken by AKG after Neumann discontinued its OEM production of the Telefunken U-47. The Golden Age Premier GA-251 MKII is inspired by this truly classic microphone. The GA-251 MKII shares the same design goal that was set for the GA-47: to offer the classic qualities and advantages that a vintage unit in perfect condition would provide and doing so at a low price point.
Mic Body and Grille
The mic body is made of brass, the grille is made of iron. The grille, which is a critical component affecting the sound character, is similar to the one in the ELA M 251.
Capsule
The GA-251 MKII uses a 34 mm K251 style capsule. Being a dual-sided one, it provides both cardioid and omni polar patterns. In order to get a good consistency between units, for each production run of 50 pcs GA-251 MKII units, approximately 200 capsules is evaluated in order to find 50 capsules with specifications that lie within the tight tolerances.
The sensitivity of the front and back side of the capsule do not differ more than 0.3 dB. The sensitivity between different capsules do not differ more than 0.5 dB. The tight manufacturing tolerance will lead to a very good consistency between different GA-251 MKII units. The capsule is specially designed to complement the electronic circuit of the GA-251 MKII to achieve a frequency response curve with a nice balance between the high, middle and low frequencies. The result is a very smooth sound with a warm bottom and airy top end just like ELA M 251.
Tube
The GA-251 MKII uses a NOS Phillip 5840W super low noise pentode tube connected in triode mode in order to decrease the noise. The tube has the following characters:
- Balanced sound response
- A smooth and warm sound character and a low noise level
- Long lifespan: The GA-251 MKII amplifier features a new proprietary circuit designed around the NOS 5840W tube.
Output Transformer
The GA-251 MKII transformer is specially designed with a 10:1 AMI style dual bobbin transformer. It is made from Permalloy steel sheet from USA and enameled wire from Germany. It offers a wonderful sound character with a high resolution and great balance between the low, middle and high frequency bands.
Capacitors and Resistors
The coupling capacitor is made by Solen from France. It is a high balanced film capacitor made from MKP material with pure oxygen-free copper connections. It has a very delicate and balanced sound. The capsule capacitor uses NOS Siemens antique grade polystyrene capacitor to reduce loss. The tube cathode bypass capacitor uses an ELNA OFC Cerafine high end hifi capacitor from Japan with oxygen free copper connections exhibiting a very sweet and delicate character, not the least for vocals. The other capacitors are of the low loss polystyrene type.
The resistor used for setting the capsule voltage is a high quality DALE 1% metal film resistor. The result is a very stable and consistent operating level leading to better consistency between different GA-251 MKII units. The plate resistor uses a non-inductive resistor of the United States IRC audio with pure copper connections. The sound level is rich and full bodied.
Mic Interior
The electronic circuit is built with point-to point wiring, All soldering points made with Mudorf Msolder Supreme silver gold solder. All of the inside wire use pure silver wire and decrease the loss during the circuit transmission, also it can ensure the sound quality is transparent.
All components which are connected to electrical ground is connected to the ground plane on the circuit board. All other component connections use point to point wiring which results in virtually zero loss and crosstalk.
Power Supply Transformer and Electrolytic Capacitors
The vintage style power supply PSU uses a high power R-style transformer with a low noise level and minimum stray field. A simple but effective circuit uses dual-stage filtering for the filament voltage. The High voltage is also precisely filtered and stabilized using an ON semiconductor zener diode.
The polar pattern switch is placed on the power supply so that the recording engineer can change the polar pattern between Cardioid and Omni remotely. A ground lift switch will help to solve mains power related noise issues that can appear in some cases
Mic Cable
The cable is specially produced using 99.99% pure oxygen-free copper, Teflon insulation, tin foil and 98% kitmesh, ie with a very high braided density of the cable shield. It has a very open and smooth sound. The mic connector is an aviation style plug providing solid connections and a long life.
- Improved, more even grille.
- The inner design is more tidy and stable using a an expensive Rogers circuit board with point-point wiring resulting in an ever more refined sound quality.
- A new metal flight case and black cardboard box.
• Hand made in small series, 50 units at a time, in a boutique style microphone workshop
• Capsules selected with very tight tolerances
• New Old Stock Phillip 5840W super low noise pentode tube connected in triode mode
• All soldering points made with Mudorf Msolder Supreme Silver Gold solder
• Solid wood microphone box, sturdy metal flight case
- Frequency range: 20Hz-20KHz
- Signal/Noise: 85dBA
- Impedance: 200 Ohm
- Sensitivity: 16mV/Pa
- Backplate material: brass
- Capsule diameter: 34 mm
- Membrane diameter: 34 mm
- Membrane material: 6 micron gold-coated mylar
- Microphone dimensions: 50mm (diameter) 250mm (length)
- Microphone weight: 0.6kg
- PSU dimensions: 200mm (length) x 100mm (width) x 100mm (height)
- PSU weight: 1.5 kg
Mic Body and Grille
The mic body is made of brass, the grille is made of iron. The grille, which is a critical component affecting the sound character, is similar to the one in the ELA M 251.
Capsule
The GA-251 MKII uses a 34 mm K251 style capsule. Being a dual-sided one, it provides both cardioid and omni polar patterns. In order to get a good consistency between units, for each production run of 50 pcs GA-251 MKII units, approximately 200 capsules is evaluated in order to find 50 capsules with specifications that lie within the tight tolerances.
The sensitivity of the front and back side of the capsule do not differ more than 0.3 dB. The sensitivity between different capsules do not differ more than 0.5 dB. The tight manufacturing tolerance will lead to a very good consistency between different GA-251 MKII units. The capsule is specially designed to complement the electronic circuit of the GA-251 MKII to achieve a frequency response curve with a nice balance between the high, middle and low frequencies. The result is a very smooth sound with a warm bottom and airy top end just like ELA M 251.
Tube
The GA-251 MKII uses a NOS Phillip 5840W super low noise pentode tube connected in triode mode in order to decrease the noise. The tube has the following characters:
- Balanced sound response
- A smooth and warm sound character and a low noise level
- Long lifespan: The GA-251 MKII amplifier features a new proprietary circuit designed around the NOS 5840W tube.
Output Transformer
The GA-251 MKII transformer is specially designed with a 10:1 AMI style dual bobbin transformer. It is made from Permalloy steel sheet from USA and enameled wire from Germany. It offers a wonderful sound character with a high resolution and great balance between the low, middle and high frequency bands.
Capacitors and Resistors
The coupling capacitor is made by Solen from France. It is a high balanced film capacitor made from MKP material with pure oxygen-free copper connections. It has a very delicate and balanced sound. The capsule capacitor uses NOS Siemens antique grade polystyrene capacitor to reduce loss. The tube cathode bypass capacitor uses an ELNA OFC Cerafine high end hifi capacitor from Japan with oxygen free copper connections exhibiting a very sweet and delicate character, not the least for vocals. The other capacitors are of the low loss polystyrene type.
The resistor used for setting the capsule voltage is a high quality DALE 1% metal film resistor. The result is a very stable and consistent operating level leading to better consistency between different GA-251 MKII units. The plate resistor uses a non-inductive resistor of the United States IRC audio with pure copper connections. The sound level is rich and full bodied.
Mic Interior
The electronic circuit is built with point-to point wiring, All soldering points made with Mudorf Msolder Supreme silver gold solder. All of the inside wire use pure silver wire and decrease the loss during the circuit transmission, also it can ensure the sound quality is transparent.
All components which are connected to electrical ground is connected to the ground plane on the circuit board. All other component connections use point to point wiring which results in virtually zero loss and crosstalk.
Power Supply Transformer and Electrolytic Capacitors
The vintage style power supply PSU uses a high power R-style transformer with a low noise level and minimum stray field. A simple but effective circuit uses dual-stage filtering for the filament voltage. The High voltage is also precisely filtered and stabilized using an ON semiconductor zener diode.
The polar pattern switch is placed on the power supply so that the recording engineer can change the polar pattern between Cardioid and Omni remotely. A ground lift switch will help to solve mains power related noise issues that can appear in some cases
Mic Cable
The cable is specially produced using 99.99% pure oxygen-free copper, Teflon insulation, tin foil and 98% kitmesh, ie with a very high braided density of the cable shield. It has a very open and smooth sound. The mic connector is an aviation style plug providing solid connections and a long life.
The MKII Version has the Following Improvements
- A new CNC produced base plate made of brass.- Improved, more even grille.
- The inner design is more tidy and stable using a an expensive Rogers circuit board with point-point wiring resulting in an ever more refined sound quality.
- A new metal flight case and black cardboard box.
Features
• High End, no compromise components and build quality• Hand made in small series, 50 units at a time, in a boutique style microphone workshop
• Capsules selected with very tight tolerances
• New Old Stock Phillip 5840W super low noise pentode tube connected in triode mode
• All soldering points made with Mudorf Msolder Supreme Silver Gold solder
• Solid wood microphone box, sturdy metal flight case
Specifications
- Maximum SPL: 136dB- Frequency range: 20Hz-20KHz
- Signal/Noise: 85dBA
- Impedance: 200 Ohm
- Sensitivity: 16mV/Pa
- Backplate material: brass
- Capsule diameter: 34 mm
- Membrane diameter: 34 mm
- Membrane material: 6 micron gold-coated mylar
- Microphone dimensions: 50mm (diameter) 250mm (length)
- Microphone weight: 0.6kg
- PSU dimensions: 200mm (length) x 100mm (width) x 100mm (height)
- PSU weight: 1.5 kg
Q & A
There are currently no questions for this product.
Reviews
There are currently no reviews for this product. Be the first to write one!
Protect your investment with the Long & McQuade Performance Warranty
A warranty can be a very important factor when making a buying decision. Because repairs can be very expensive in terms of parts and labour costs, manufacturers usually only provide one year limited warranties that generally only cover items that malfunction due to a manufacturer’s defect. With an important purchase such as a musical
instrument or piece of studio gear, however, many people want to have the peace of mind in knowing that their investment will be protected should the product no longer be performing at 100%.
Because of this, Long & McQuade provides our customers with a FREE one-year Performance Warranty on most of our products. The Long & McQuade Performance Warranty supplements the manufacturer’s warranty to ensure that our customers receive complete “no hassle” warranty coverage within their first year.
How does the Long & McQuade Performance Warranty differ from most manufacturers' warranties?
- Performance Guarantee: Normal wear and tear is covered, so your product will be performing as well as the day you purchased it for the entire duration of the coverage. Band and Orchestral Performance Warranty does not include replacing pads or cleaning for woodwind instruments, unless deemed necessary by our repair staff. Ultrasonic cleaning for brass instruments will be provided if deemed necessary by our repair staff, but is not routinely offered under the Performance Warranty.
- Product Replacement: If your product cannot be fixed or costs too much to fix, we will replace it with the equivalent model for no additional charge. If this is not possible, a full refund will be provided.
- No Lemon Policy: Your product will be replaced should the same problem occur multiple times.
- Convenient: Easy drop off and pick up of the product at any Long & McQuade location.
- Guitar Setup: Guitars purchased at Long & McQuade come with 1 free setup, to be redeemed within 1 year for new guitars and 90 days for used guitars.
- Loaners Available: A loaner product may be given while the product is being repaired.
- Power Surge Protection: Your product is covered even if damaged from a power surge.
- Accessory Coverage: Any peripheral devices or accessories that come with your product (i.e. foot pedal, case) are also covered.
- Commercial Use Coverage: Music and recording professionals who purchase gear for “heavy-use” commercial purposes will still be covered.
Long & McQuade reserves the right to restrict the purchase of additional years of Performance Warranty. Used products come with a 3-month Long & McQuade Performance Warranty. Some products (i.e. computers, software, cymbals and other items) are covered only by the manufacturer‘s warranty. Consumables (i.e. strings, reeds, drum sticks, batteries, tubes, cross faders) are excluded as they are designed to be replaced. Cosmetic Damage, Accidental Damage, or problems caused by Humidity or Temperature Issues are not covered. Speakers damaged by overpowering are generally not covered. Our coverage does not provide compensation for loss of use. As of June 2018 the Performance Warranty is no longer transferable. The warranty is only valid in Canada.
Purchasing additional years of coverage
Some manufacturers provide warranties for longer than 1 year; however, these are usually limited warranties that do not provide the same coverage as the Long & McQuade Performance Warranty. Customers interested in more complete and convenient (but not necessarily longer) coverage are still able to purchase additional years of the Performance Warranty.
If you are interested in receiving this coverage for longer than one year, you have the option of purchasing additional years of the Performance Warranty. The pricing is as follows:
- NEW products: Starting at 4% of the current new selling price to double the warranty from 1 year to 2 years. Starting at 4% for each additional year.
- USED products: Starting at 4% of the current new selling price to increase the warranty from 3 months to 1 year. Starting at 4% for each additional year.
- GUITARS: 4% of the current new selling price to double the warranty from 1 year to 2 years. 4% for each additional year. $45 maximum. An additional free setup is not included with additional purchased years of Performance Warranty.
- BAND and ORCHESTRAL instruments: 4% of the current new selling price to double the warranty from 1 year to 2 years. 4% for each additional year.
Great Additions
Reserve in Store
| Product | SKU | Qty |
|---|---|---|
| GA-251 MKII Large Diaphragm Tube Condenser Microphone | 814429 |
